Aluminum Ingots: Tested for purity using optical emission spectroscopy (OES) to confirm aluminum content ≥99.5%. Mechanical properties (tensile strength ≥120MPa, elongation ≥15%) are evaluated using a universal testing machine to ensure suitability for drawing and stranding.
XLPE Pellets: Melt flow rate (MFR) is measured at 190℃/2.16kg, with a standard range of 0.5g/10min to 2.0g/10min to verify processability. Moisture content is tested via Karl Fischer titration, with a maximum allowable limit of 0.05% to prevent insulation defects like bubbles or voids. UV stabilizer and antioxidant content are also verified through chemical analysis to ensure long-term aging resistance.
Drawn Aluminum Wires: Inspected for diameter (1.2mm to 1.8mm) using a laser micrometer, with a tolerance of ±0.02mm. Tensile strength (≥140MPa) and electrical conductivity (≥61% IACS) are tested on random samples to confirm performance after cold working.
Stranded Conductors: Measured for outer diameter (typically 4.5mm to 5.5mm for 16 mm²) and DC resistance (≤1.83Ω/km at 20℃) using a four-wire micro-ohmmeter. Stranding uniformity is checked visually and via a profile projector to ensure consistent lay length and wire alignment—any loose or overlapping wires result in rejection.
Insulated Conductors: Tested for insulation thickness (2.5mm to 3.0mm) using an ultrasonic thickness gauge, with a tolerance of ±0.1mm. Dielectric strength is evaluated by applying 30kV AC for 1 minute (no breakdown allowed). Insulation resistance is measured using a 10kV megohmmeter, requiring ≥10¹²Ω·m. Thermal stability is assessed by heating samples to 130℃ for 168 hours and measuring post-exposure tensile strength retention (≥80%).
Electrical Tests:
Conductor Resistance Test: Measures the DC resistance of the 16 mm² stranded conductor at 20℃, with a maximum limit of ≤1.83Ω/km. This ensures minimal power loss during medium-voltage transmission.
Insulation Resistance Test: Evaluates insulation resistance between the conductor and ground (simulated by a metal foil wrapped around the insulation) using a 10kV megohmmeter. A minimum resistance of ≥10¹²Ω·m confirms effective insulation against current leakage.
Dielectric Withstand Test: Submerges the cable in a 25℃ water bath for 1 hour to simulate outdoor moisture conditions, then applies 25kV AC for 5 minutes. No breakdown or leakage current exceeding 50μA is allowed, verifying the insulation’s ability to withstand 10kV operation safely.
Partial Discharge Test: Conducted at 1.73× rated voltage (17.3kV) to detect internal defects in the XLPE insulation. Partial discharge magnitude must be ≤10pC, as excessive partial discharge can lead to insulation degradation and premature failure in MV applications.
Mechanical Tests:
Tensile Test: Pulls the cable to its breaking point to measure overall tensile strength (≥800N) and elongation at break (≥15%), ensuring it can withstand the mechanical tension of overhead installation and wind loads.
Bending Test: Bends the cable around a mandrel with a diameter of 15× the cable’s outer diameter (static bending) and 20× the outer diameter (dynamic bending) for 10 cycles each. After bending, the insulation is inspected for cracks, and dielectric strength is re-tested to confirm no damage.
Impact Test: Drops a 1kg weight from a 1m height onto the cable (per IEC 60811-1-1). Post-impact, the cable is tested for insulation resistance and dielectric strength—no significant drop in performance is allowed.
Environmental Tests:
UV Resistance Test: Exposes the cable to a xenon arc lamp (42W/m² at 340nm) for 1000 hours to simulate long-term sunlight exposure. Post-test, the insulation’s tensile strength retention is ≥80%, and no surface cracking or discoloration is permitted.
Temperature Cycling Test: Subjects the cable to 50 cycles of -40℃ (4 hours) and 90℃ (4 hours) to simulate extreme weather variations. After cycling, insulation resistance and dielectric strength are re-evaluated, with no more than a 10% reduction in performance allowed.
Water Immersion Test: Submerges the cable in deionized water at 60℃ for 1000 hours. Post-immersion, insulation resistance is ≥10¹¹Ω·m, confirming resistance to moisture ingress—critical for outdoor overhead operation in rainy or humid regions.
Inner Layer: A 25μm-thick polyethylene (PE) film is tightly wrapped around the spooled cable, heat-sealed at the seams to form a moisture-proof barrier. This prevents dust, rain, or dew from penetrating the cable during transit.
Middle Layer: A woven polypropylene (PP) bag (80g/m²) is slipped over the PE-wrapped reel. Woven PP offers high abrasion resistance (tensile strength ≥180N/50mm) and protects against scratches or impacts during handling.
Outer Layer: For wooden reels, a 5mm-thick plywood cover is attached to both flanges using galvanized screws. This cover shields the cable ends from damage and prevents foreign objects from getting caught in the reel. For fiberglass reels, a 4mm double-wall corrugated cardboard cover is used, which is lightweight and recyclable while still providing adequate protection.
Wooden Pallets: ISPM 15-treated softwood (pine) with dimensions 1200mm × 1000mm (EU standard) or 1200mm × 800mm (US standard). Load capacity: ≥1200kg.
Plastic Pallets: High-density polyethylene (HDPE) pallets with the same dimensions as wooden pallets. They are lightweight (25kg vs. 40kg for wooden pallets), moisture-resistant, and reusable, making them ideal for international shipments or humid environments.
12mm-wide polyester straps, tensioned to 400N to 600N, wrapped around the perimeter of the pallet and over the reels.
40μm-thick linear low-density polyethylene (LLDPE) stretch film, wrapped in 4 to 6 layers around the entire pallet to prevent shifting during transit.
80mm × 80mm × 40mm wooden blocks placed between reels to distribute weight evenly and avoid friction between reel flanges.
Truck Transportation: Suitable for 1 to 6 reels (500m to 2000m each). Trucks are equipped with either enclosed or flatbed trailers:
Enclosed Trailers: Preferred for long distances or adverse weather (rain, snow). They provide full protection against the elements and have a load capacity of 15,000kg. Temperature inside the trailer is monitored to avoid extreme heat or cold that could damage the cable.
Flatbed Trailers: Used for oversized reels (diameter >1.2m) that cannot fit in enclosed trailers. Reels are secured with chains and covered with waterproof, UV-resistant tarpaulins to protect against weather and road debris.
Rail Transportation: Ideal for large-volume shipments (6+ reels) or long distances (400km+). Railcars with flatbeds or covered wagons are used, with a load capacity of 25,000kg per car. Reels are secured using wooden dunnage and steel straps to prevent movement during transit. Rail transportation is 25% cheaper than trucking for long distances and reduces carbon emissions by 55% per ton-kilometer, aligning with sustainability goals.
Container Shipping: Reels are loaded into 20-foot or 40-foot standard containers:
20-foot Container: Holds 4 to 5 wooden reels (1000m each) or 5 to 6 fiberglass reels (800m each). Gross weight limit: 24,000kg.
40-foot Container: Holds 8 to 10 wooden reels (1000m each) or 10 to 12 fiberglass reels (800m each). Gross weight limit: 28,000kg.
Break-Bulk Shipping: Used for oversized reels (diameter >1.5m) that cannot fit in containers. Reels are loaded directly onto the ship’s deck using cranes with spreader bars. They are secured with heavy-duty chains and turnbuckles, and additional steel frames are installed around the reels to protect against impact from seawater or debris.
Cargo Planes: Reels are transported in the belly of passenger planes or dedicated cargo planes (e.g., Boeing 777F, Airbus A330F). Weight limit per reel: 120kg (due to aircraft cargo hold constraints). Reels are packaged in lightweight foam-lined cardboard boxes to minimize weight and absorb shocks during takeoff and landing.
Regulations: Compliance with IATA (International Air Transport Association) regulations, including proper labeling (e.g., “Heavy Cargo,” “Handle with Care”) and security screening. All documentation (commercial invoice, packing list) must be completed accurately to avoid customs delays.
Commercial Invoice: Details the product description, quantity, unit price, total value, and payment terms. It is used for customs valuation and financial record-keeping.
Packing List: Itemizes each reel (reel number, length, weight, batch number) to facilitate carrier verification and customs inspection.
Certificate of Compliance (CoC): Issued by the quality control department, confirming the cable meets IEC 60502-2 and GB/T 14049-2018 standards. It includes key test results (e.g., conductor resistance, insulation resistance).
Certificate of Origin (CoO): Verified by a chamber of commerce, confirming the cable’s manufacturing location. It may qualify the customer for import duty exemptions under trade agreements (e.g., ASEAN Free Trade Area, CPTPP).
ISPM 15 Certificate: For wooden reels, confirms compliance with international phytosanitary regulations to prevent the spread of pests.
Domestic Trucking: Departure from the manufacturer’s warehouse, arrival at regional distribution hubs, estimated time of arrival (ETA) at the customer’s site, and proof of delivery.
Sea Shipping: Departure from the origin port, arrival at transshipment ports (if applicable), arrival at the destination port, customs clearance status, and pickup from the port.
Air Shipping: Departure from the origin airport, arrival at the destination airport, customs clearance, and final delivery to the customer’s site.
Dispatch Confirmation: Sent within 24 hours of pickup, including the carrier’s name, tracking number, ETA, and contact information for the carrier’s local representative.
In-Transit Update: For long-distance shipments (e.g., sea shipments exceeding 3 weeks), the team provides a mid-transit update, confirming the shipment’s location and any adjustments to the ETA (e.g., delays due to weather or port congestion).
Customs Clearance Alert: For international shipments, the team notifies the customer when the shipment arrives at the destination port and initiates customs clearance. They provide guidance on any additional documentation required (e.g., import permits for certain countries) and update the customer on clearance progress, typically resolving any issues (e.g., missing documents) within 1 to 3 days.
Final Delivery Alert: Sent 24 to 48 hours before the shipment’s scheduled arrival at the customer’s site, reminding the customer to prepare for receipt—such as arranging equipment (forklift, crane) for unloading reels, clearing a storage area, and ensuring a representative is present to inspect the shipment.
Reel Condition: Inspect for cracked flanges, broken hubs, or loose cable ends. For wooden reels, check for signs of moisture damage (e.g., warping, mold) or pest infestation (though ISPM 15 treatment minimizes this risk). For fiberglass reels, check for cracks or chips in the reel body.
Packaging Condition: Verify that the PE film, PP bag, and outer cover (plywood or cardboard) are intact. Any tears, punctures, or missing packaging may indicate rough handling during transit.
Cable Condition: If packaging is damaged, visually inspect the cable for scratches, cracks, or discoloration of the XLPE insulation. For suspected damage, the customer can perform a basic insulation resistance test using a megohmmeter (with the manufacturer’s guidance) to check for insulation integrity.
Confirm satisfaction with the shipment, including the condition of the reels and cable, adherence to the ETA, and quality of the carrier’s service.
Address any questions about storage or handling of the cable—such as recommended storage conditions (dry, well-ventilated area, away from heat sources) or best practices for unwinding the cable during installation.
Collect feedback on the shipping process, including areas for improvement (e.g., more frequent updates, better packaging for international shipments) to enhance future customer experiences.
Sample Purpose: Testing (electrical, mechanical, environmental), demonstration to stakeholders (e.g., project managers, utility companies), or qualification for a specific medium-voltage project (e.g., rural grid upgrade, industrial park expansion).
Sample Specifications: Confirmation of the 10kV voltage rating, 16 mm² aluminum conductor, and XLPE insulation (standard for this product), along with the required length—typical sample lengths range from 1m to 5m, though custom lengths up to 10m are available upon request.
Delivery Details: The customer’s full address (including any access restrictions, e.g., gated communities, limited delivery hours), contact person, phone number, and email address for tracking updates.
Testing Requirements: If the customer intends to conduct specific tests (e.g., dielectric withstand, UV resistance), the team notes these to include relevant test data (e.g., certificate of analysis for XLPE insulation) with the sample.
Conductor Preparation: A section of the 16 mm² stranded aluminum conductor is cut from the same batch used for full-length cables, ensuring consistent purity (≥99.5%) and stranding pattern (7 wires, lay length 12-16× outer diameter).
XLPE Insulation Extrusion and Cross-Linking: The conductor section is coated with XLPE insulation using the same extruder and cross-head die as full-length cables, with insulation thickness controlled to 2.5mm to 3.0mm. The insulated sample undergoes peroxide cross-linking at 200℃ to 250℃ for 6 to 10 minutes, followed by rapid cooling to room temperature.
Trimming and Finishing: The sample is trimmed to the requested length, with the ends cleaned to remove any insulation burrs. For ease of testing, the conductor ends may be stripped (10mm to 20mm of insulation removed) to allow for electrical connections.
Dimensional Checks: Conductor cross-sectional area (16 mm²), insulation thickness (2.5mm to 3.0mm), and overall sample diameter (8mm to 10mm) are measured using a laser micrometer and ultrasonic thickness gauge to confirm compliance with specifications.
Electrical Testing: Insulation resistance is measured using a 10kV megohmmeter, requiring ≥10¹²Ω·m at 20℃. A dielectric withstand test is conducted at 25kV AC for 1 minute, with no breakdown or leakage current exceeding 50μA allowed.
Visual Inspection: The sample is checked for surface defects—such as bubbles, scratches, or uneven insulation coating—and the stranded conductor is inspected for loose or overlapping wires.
Cable Specifications: 10kV Single Core Overhead Cable, 16 mm² Aluminum Conductor, XLPE Insulated.
Sample Details: Length (e.g., “Sample Length: 2m”), Batch Number (matching the batch used for full-length cables for traceability), and Production Date.
Handling Instructions: “Do Not Bend Below Minimum Radius (120mm)” (15× the sample’s outer diameter of 8mm) to avoid damage to the XLPE insulation; “Store in Dry, Cool Area” to prevent moisture damage.
Manufacturer Information: Name, contact phone number, email address, and website for technical support or additional inquiries.
Confirm the sample arrived in good condition and meets the customer’s expectations regarding appearance (e.g., smooth insulation, uniform conductor stranding), flexibility (ease of bending for installation), and build quality.
Address technical questions related to the sample, such as how to conduct specific tests (e.g., partial discharge testing, thermal cycling) or how the cable’s performance compares to other medium-voltage cables (e.g., copper-conductor or EPR-insulated cables). The team may also provide additional resources, such as technical datasheets or application guides, to support the customer’s evaluation.
Review test results: If the customer conducted their own tests, the team discusses the findings, provides context for any deviations from expected results (e.g., minor variations in insulation thickness within tolerance), and offers technical explanations to resolve concerns (e.g., why insulation resistance may be slightly lower at high humidity).
Explore next steps: If the customer is satisfied with the sample, the team presents a formal quote for full-order quantities, including pricing (based on volume), lead times (7 to 14 days for standard lengths), and shipping options. If modifications are needed (e.g., a different conductor size, enhanced UV resistance), the team collaborates with the engineering department to develop a customized solution and provides a revised sample if required.
Toll-Free Hotline: Staffed by engineers who can provide immediate assistance for critical issues, such as troubleshooting insulation failures or advising on emergency repairs. The hotline is monitored 24/7, with an average response time of less than 15 minutes for urgent calls.
Email/Video Call: For detailed technical discussions (e.g., complex installation challenges, performance optimization), the team responds to emails within 4 hours and schedules video calls (via Zoom, Microsoft Teams) at the customer’s convenience to provide visual guidance.
Online Support Portal: A self-service platform featuring a wealth of resources tailored to medium-voltage applications:
Installation Manuals: Step-by-step guides with diagrams covering cable unwinding, tensioning, connection to substations or distribution boxes, and compatibility with hardware (e.g., insulators, clamps).
Technical Datasheets: Detailed specifications, including current-carrying capacity at different temperatures, voltage drop calculations, and mechanical properties (tensile strength, bending radius).
FAQs: Answers to common questions, such as “How to repair a minor insulation scratch?” “What is the maximum span between poles for the 16 mm² cable?” and “How to test for partial discharge in the field?”
Video Tutorials: Demonstrations of key processes, such as proper cable handling, insulation resistance testing, and maintenance procedures.
Installation Guidance: For large-scale projects (e.g., rural grid upgrades, industrial park power supply), the team can provide on-site support: an engineer visits the customer’s site to supervise installation crews, train workers on best practices (e.g., maintaining proper tension during overhead 敷设，avoiding sharp bends), and resolve on-site challenges (e.g., navigating obstacles like trees or rivers, adjusting for uneven terrain). The engineer also conducts a pre-installation inspection of the site to ensure compatibility with the cable’s specifications (e.g., pole load capacity, span length).
Performance Optimization: Advising customers on how to maximize the cable’s efficiency and lifespan, such as:
Load Management: Providing guidelines for current loading to avoid overheating—for the 16 mm² conductor, the maximum continuous load at 90℃ is 85A, with short-term overloads (up to 130℃) limited to 5 seconds. The team may also recommend installing current monitoring systems to track load levels and prevent overloading.
Environmental Adaptation: Recommending additional protections for extreme conditions, such as applying a UV-resistant coating for cables installed in high-sunlight regions (e.g., deserts), using waterproof joint sleeves for coastal areas with high humidity, or installing ice shields for regions with heavy snowfall.
Troubleshooting: Diagnosing and resolving issues to minimize downtime, such as:
Electrical Faults: For low insulation resistance (caused by moisture ingress), the team recommends drying the affected section using compressed air and resealing joints with heat-shrink sleeves; for partial discharge (indicating internal insulation defects), they advise replacing the damaged section of cable to prevent complete insulation failure.
Mechanical Damage: For minor insulation scratches (less than 0.5mm deep), the team suggests using XLPE repair tape to seal the damage; for more severe damage (e.g., insulation cracks penetrating the full thickness), the team coordinates with the customer to schedule a site visit by a certified technician, who will remove the damaged section and splice a new segment using medium-voltage-compatible splice kits (ensuring the splice meets IEC 60840 standards for electrical performance).
Environmental Damage: For UV-induced insulation brittleness (common in long-term exposure to intense sunlight), the team recommends applying a UV-resistant silicone coating to extend the cable’s service life; for corrosion of conductor terminations (in coastal areas), they advise cleaning the terminations with a specialized aluminum cleaner and applying an anti-corrosion compound to prevent further degradation.
Conductor Defects: Cracks, breaks, or excessive DC resistance (exceeding 1.83Ω/km at 20℃) caused by faulty aluminum material or improper stranding. This includes conductor deformation due to manufacturing errors (e.g., uneven stranding tension) that impairs electrical conductivity.
XLPE Insulation Defects: Premature aging (brittleness, cracking) within the 15-year warranty period, dielectric breakdown under rated voltage (10kV), or delamination between the insulation and conductor—all resulting from substandard XLPE material or incorrect extrusion/cross-linking processes. Partial discharge levels exceeding 10pC at 17.3kV (1.73× rated voltage) are also covered, as this indicates internal insulation defects.
Manufacturing Defects: Issues arising from flawed production processes, such as inconsistent insulation thickness (outside the ±0.1mm tolerance), uneven conductor stranding, or poor adhesion between the conductor and insulation.
Damage from improper installation (e.g., bending below the minimum radius, over-tensioning the cable during 敷设，using incompatible hardware like non-medium-voltage insulators).
Damage from misuse or abuse (e.g., operating the cable at voltages exceeding 10kV, exposing it to harsh chemicals not specified in the material safety data sheet (MSDS), physical damage from vehicle collisions with utility poles or construction equipment).
Normal wear and tear (e.g., minor surface scratches on the insulation that do not affect electrical performance, slight increases in conductor resistance within industry-accepted limits—≤5% over the warranty period).
Damage from natural disasters (e.g., floods, tornadoes, wildfires) or extreme weather conditions beyond the cable’s design limits (-40℃ to 90℃), such as ice loads exceeding 50N/m or wind speeds exceeding 120km/h.
Notification: The customer must notify the manufacturer in writing within 30 days of discovering the defect. The notification must include:
Order number, delivery date, and batch number (from the reel label).
A detailed description of the defect (e.g., “XLPE insulation cracked 200m from the substation,” “Conductor resistance measured at 2.1Ω/km, exceeding the maximum limit”).
Supporting evidence: High-resolution photographs/videos of the defect, test reports (e.g., insulation resistance measurements, partial discharge test results), and a copy of the installation records (to rule out improper installation).
Verification: The manufacturer’s quality control team reviews the claim and supporting documents within 48 hours. For complex defects, the team may:
Request a small sample of the defective cable (50cm-1m) for laboratory testing (at the manufacturer’s expense) to confirm the root cause—tests may include dielectric withstand, Fourier-transform infrared (FTIR) spectroscopy (to analyze insulation degradation), or conductor purity analysis.
Dispatch a technical engineer to the customer’s site for on-site inspection (within 3-5 days for domestic customers, 7-10 days for international customers) to assess the defect’s severity and its impact on the medium-voltage network.
Resolution: If the claim is approved, the manufacturer offers a resolution tailored to the defect’s nature and the customer’s operational needs:
Replacement: For fully defective cables (e.g., widespread insulation failure), new cables of the same specification (10kV, 16 mm² aluminum conductor, XLPE insulation) are manufactured and shipped to the customer free of charge, including all transportation and customs costs (for international orders). The manufacturer coordinates with the customer to schedule delivery during off-peak hours (e.g., nighttime for live medium-voltage lines) to minimize network downtime.
Repair: For localized defects (e.g., a 50m section with insulation damage), the manufacturer provides a medium-voltage repair kit (containing XLPE repair tape, heat-shrink sleeves, and conductive grease for terminations) along with step-by-step instructions. For critical repairs (e.g., near substations), a certified technician is dispatched to perform the work, ensuring compliance with safety standards (e.g., IEEE 524 for cable splicing).
Refund: If the customer prefers not to receive a replacement or repair, a partial or full refund is issued based on the proportion of defective cable length. Refunds are processed within 5-7 business days of resolution approval, with funds transferred to the customer’s designated bank account.
Closure: After the resolution is implemented, the manufacturer follows up with the customer within 2 weeks to confirm satisfaction. A formal warranty claim report is provided, documenting the defect, investigation findings, resolution measures, and post-repair test results (e.g., insulation resistance after splicing). This report is archived in the manufacturer’s database for traceability and used to identify trends for quality improvement (e.g., recurring insulation defects in a specific production batch).
Basic Information: Order number, delivery date, cable batch number, and contact details (name, phone number, email).
Complaint Details: A clear description of the issue (e.g., “Cable delivery delayed by 10 days,” “Technical support failed to respond to a partial discharge inquiry”), the date the issue was discovered, and its impact on the customer’s project (e.g., “Rural grid upgrade delayed, affecting 200 households”).
Supporting Evidence: Photographs (e.g., damaged cable insulation), delivery receipts, communication records (e.g., email threads with technical support), or test reports to validate the complaint.
Critical: Issues that pose immediate safety risks (e.g., short circuits caused by insulation failure) or completely halt the customer’s medium-voltage project. These are prioritized with a response required within 24 hours and a resolution plan finalized within 3 days.
Major: Issues that affect cable performance but do not pose safety risks (e.g., conductor resistance slightly above specifications) or cause significant project delays (e.g., 1-week shipment delay). These are addressed within 48 hours of receipt, with resolution completed within 7 days.
Minor: Issues that do not impact performance or project timelines (e.g., incorrect labeling on a reel, minor damage to packaging that does not affect the cable). These are resolved within 72 hours, with a focus on quick corrective action (e.g., sending corrected labels via express mail).
Product Quality Issues: The quality control team reviews production records (e.g., extrusion temperature logs, cross-linking time data) for the affected batch and conducts comparative testing with non-defective cables from the same batch. For example, if insulation cracking is reported, the team tests the XLPE’s cross-linking degree (using differential scanning calorimetry) to determine if it meets the required standard (≥70% cross-linking).
Shipping Delays: The logistics team works with the carrier to obtain detailed transit records (e.g., GPS tracking data, customs clearance timestamps) and interviews carrier personnel to identify delays caused by carrier error (e.g., missed pickups), weather events (e.g., port closures due to storms), or documentation gaps (e.g., missing customs forms).
Service Gaps: The technical support team reviews call logs, email exchanges, and ticket records to identify breakdowns—such as missed follow-ups, incorrect technical advice, or long response times. For example, if a customer reports a delayed response to a partial discharge inquiry, the team audits the support ticket system to determine if the inquiry was routed to the correct engineer.
For quality defects: Provide replacement cables, repair kits, or on-site technical support (consistent with warranty claim processes for covered issues). For example, if a batch of cables has inconsistent insulation thickness, the manufacturer replaces all affected cables and offers a 5% discount on the customer’s next order as compensation for delays.
For shipping delays: Offer compensation such as a 10% discount on the customer’s next order, free expedited shipping for a replacement shipment, or reimbursement for additional costs incurred (e.g., overtime labor for delayed installation). The logistics team also implements corrective actions—such as switching to a more reliable carrier or adding redundant documentation checks—to prevent future delays.
For service gaps: Provide additional training for technical support engineers (e.g., a workshop on medium-voltage partial discharge testing), assign a dedicated account manager to the customer for personalized support, or revise the support ticket system to reduce response times (e.g., setting a 2-hour SLA for urgent inquiries).
Production: If multiple complaints relate to XLPE insulation defects, the production team adjusts the extrusion temperature profile or sources XLPE pellets from a more reliable supplier. For example, if insulation bubbles are linked to insufficient drying of XLPE pellets, the team increases the drying time from 2 hours to 4 hours.
Logistics: If a carrier consistently causes delays, the logistics team replaces the carrier and updates the carrier selection criteria to include stricter on-time delivery requirements (minimum 95% on-time rate for the past year).
Service: If customers frequently report unclear installation manuals, the technical support team revises the documentation to include more detailed diagrams, step-by-step videos, and FAQs tailored to medium-voltage applications (e.g., “How to calculate cable tension for 50m spans”).
Mild Environments (Urban Suburbs, Temperate Climates): Inspect every 2 years.
Moderate Environments (Industrial Peripheries, Humid Regions): Inspect every 1 year.
Harsh Environments (Coastal Areas, Deserts, Cold Climates): Inspect every 6 months.
Visual Inspection:
XLPE Insulation: Check for signs of aging (discoloration, brittleness), cracking, or damage from external objects (e.g., tree branches, bird pecking). Pay special attention to areas near utility poles and terminations—these are high-stress points where insulation damage is most likely to occur. In coastal areas, look for salt deposits on the insulation surface, which can accelerate degradation.
Aluminum Conductor: If insulation is damaged, inspect the conductor for signs of corrosion (greenish-white deposits) or deformation. Ensure the conductor remains straight and properly aligned in insulators—sagging beyond 0.5m between poles (for 50m spans) indicates potential tension loss or conductor stretching.
Terminations and Splices: Inspect conductor terminations (e.g., connections to substations, distribution boxes) and splices for signs of overheating (discoloration of insulation), loose connections, or corrosion. Overheating indicates poor electrical contact, which can increase power loss and risk fire.
Electrical Testing:
Insulation Resistance Test: Use a 10kV megohmmeter to measure insulation resistance between the conductor and ground (simulated by a metal foil wrapped around the insulation). The resistance should remain ≥10¹²Ω·m; a significant drop (e.g., below 10¹¹Ω·m) indicates moisture ingress or insulation degradation. Test results should be recorded and compared to previous measurements to track trends over time.
Conductor Resistance Test: Use a micro-ohmmeter to measure the DC resistance of the 16 mm² conductor at 20℃. The resistance should not exceed 1.83Ω/km; an increase of more than 5% from the initial installation test results indicates conductor corrosion or damage.
Partial Discharge Test: Conducted at 1.73× rated voltage (17.3kV) using a partial discharge detector. Partial discharge magnitude must be ≤10pC—exceeding this limit indicates internal insulation defects (e.g., voids, delamination) that can lead to dielectric breakdown over time.
Voltage Drop Test: Measure voltage drop along the cable during peak load conditions (e.g., evening hours for residential areas, daytime for industrial parks). A voltage drop exceeding 3% of the rated voltage (10kV) indicates overloading, poor terminations, or conductor damage—all of which require immediate correction to prevent power outages.
Mechanical Inspection:
Tension Check: Use a cable tension meter to verify the cable maintains the recommended tension (600N to 800N for 50m spans). If tension is too low, the cable may sag excessively and come into contact with obstacles; if too high, it can stretch the conductor and damage the insulation. Adjust tension using pole-mounted tensioners, following the manufacturer’s guidelines for incremental adjustments (no more than 5% of the total tension per adjustment).
Bending Radius Check: Ensure the cable has not been bent below the minimum static bending radius (15× outer diameter) or dynamic bending radius (20× outer diameter). Bends beyond these limits can cause permanent damage to the XLPE insulation, increasing the risk of short circuits. Use a radius gauge to measure bends near poles or obstacles.
Insulation Protection:
UV Protection: For cables installed in high-sunlight regions (e.g., deserts, open rural areas), apply a UV-resistant silicone coating every 5 years. The coating should be compatible with XLPE (tested for adhesion and chemical compatibility) and applied in a thin, uniform layer to avoid adding excessive weight.
Moisture Prevention: Seal all terminations and splices with waterproof heat-shrink sleeves or butyl rubber tape. For coastal areas, add an additional layer of EPDM rubber tape to protect against saltwater spray. Inspect these seals every 6 months and reapply if signs of wear (e.g., cracking, peeling) are detected.
Cleaning: In industrial areas or regions with high pollution, clean the insulation surface every 12 months using a mild detergent solution (pH 6-8) and a soft brush. Avoid harsh chemicals (e.g., acetone, gasoline) that can dissolve the XLPE. Rinse thoroughly with clean water and dry with a lint-free cloth to prevent moisture retention.
Conductor Maintenance:
Corrosion Prevention: In coastal or high-humidity areas, inspect conductor terminations every 6 months. If corrosion is detected, disconnect the termination, clean it with a specialized aluminum cleaner (avoiding abrasive materials that can scratch the conductor), and apply an anti-corrosion compound (e.g., zinc-rich grease) before reconnecting. Tighten terminations to the manufacturer’s recommended torque (20N·m to 25N·m for 16 mm² conductors) to ensure good electrical contact.
Overload Management: Use a current monitoring system to track the load on the cable. Avoid continuous operation above 80% of the maximum current-carrying capacity (68A for the 16 mm² conductor at 90℃) to prevent overheating and insulation aging. If overloading is persistent, consider upgrading to a larger conductor size (e.g., 25 mm²)
Công ty TNHH Công nghệ Cáp Hongtai
E-mail: export@qlcables.com
sales@qlcables.com
Tel/WhatsApp:+86-18032066271
Thêm khu vực phát triển công nghiệp Xiaokou, Hạt Ningjin, Thành phố Xingtai ， tỉnh Hà Bắc, Trung Quốc
Bản quyền © Công ty TNHH Công nghệ Cáp Hongtai Hỗ trợ kỹ thuật:Công nghệ Ronglida
Trang web này sử dụng cookie để đảm bảo bạn có được trải nghiệm tốt nhất trên trang web của chúng tôi.
English
Español
Portugues
Pусский
Français
العربية
ไทย
Türk dili
Indonesia
Điện thoại
Thư